From the Loftsmith Workshop
Christmas tree branch holder ring, split, 16-40 mm poles
Gives an artificial tree's branches a proper place to sit on the trunk pole. The ring comes in two halves that close around the pole, and each branch rests in its own slot. Change the pole size, the slot count and the wire thickness to match your tree.
2 parts · 23 g · 75 × 37 × 24 mm
Loading the 3D view
Loading the 3D view
No adjustable sizes
Ask for the sizes you want to tweak, e.g. “make the width adjustable”.
How to print it
Parts
- ring half ×2 · PETG · Flat as modelled: ears on the bed, clamp collar on top. No supports.
The two halves are identical. Each is 75 x 37 x 24 mm at the default size, about 11 g and 21 minutes (2 walls, 15% infill). PETG because attic storage can get too warm for PLA.
Print settings
- Layer height
- 0.2 mm
- Walls
- 3 recommended (the page stats use 2)
- Infill
- 15%
- Supports
- None
- Notes
- At 2 walls and 15% infill both halves together take about 24 g and 43 minutes (default size, build report). With the recommended 3 walls they take about 32 g and 58 minutes; the extra wall puts more material round the pin and screw holes. PETG, both halves on one plate.
Hardware
- 2 × M3 x 12 mm socket head screw · Clamps the two halves together through the collar. One goes in from each side.
- 2 × M3 hex nut · Slides into the hex pocket on the side of the collar opposite each screw head.
- 8 × Steel hinge pin, 3 mm diameter, about 11 mm long · One per branch at the default 8 slots. Cut from 3 mm steel rod, a nail or stiff wire, or reuse the pins from the old ring. Length is the branch wire diameter plus about 6 mm. The hole is pin diameter
Assembly
- Measure first: the pole diameter with calipers, and the thickness of one branch wire where it enters the old ring. Set the Pole diameter and Branch wire diameter sliders to those values and the Branch slots slider to your ring's branch count, or the next even number up.
- Print two ring halves. Press an M3 nut into the hex pocket on the side of each collar, flat side first.
- Hold the halves round the pole at the tier's old height with the collars facing the same way. Fit an M3 x 12 screw through each counterbore into the nut on the other half. Tighten them evenly with a 2.5 mm hex key until the ring no longer slides; the 1.6 mm gaps between the halves should stay roughl
- Drop each branch's wire eye into a slot from the top, then push a hinge pin through the side of the ear and through the eye until both ends sit just inside the ear. A drop of glue on the pin ends stops them working loose.
- Swing each branch down into its open position. To store the tree, fold them back up along the pole.
Good to know
- Measure your old ring first. This ring suits branches whose wire ends in an eye or hook that hangs on a cross pin. Branches that hook straight into a hole in the ring need a different holder.
- Slot counts are even (4, 6, 8 or 10), so the two halves are identical. For a 7-branch ring, print 8 slots and leave one empty; the branch spacing will be slightly different from the original. 12-slot rings are not covered.
- Only round poles from 16 to 40 mm are covered. The bore matches the pole size you set, and the halves clamp together across a 1.6 mm gap, so measure the pole to about 0.5 mm.
- The grip check assumes each M3 screw is tightened to about 400 N of clamp force with 0.25 friction on the pole. Those are estimates, not measurements. The ring has not been printed or tested on a real tree.
- Each slot is checked at six times the branch weight set on the Weight per branch slider (50-400 g), to allow for a knock and for the branch levering against the ring. The tree's own design sets how far the branches open; the ring only supplies the hinge.
- The hinge pins are a light press fit that depends on your printer. If a pin is loose, glue it; if it is too tight, open the hole with a 3 mm drill.
Comments