From the Loftsmith Workshop
Portable monitor VESA 75/100 mount for 5-14 mm screens
Gives a thin portable monitor a proper place on a VESA arm or stand. Two hooks grab the top and bottom edges, and two orange knobs let you tighten it down. Set your screen's height and edge thickness and it fits.
5 parts · 88 g · 116 × 32 × 239 mm
Ask for the sizes you want to tweak, e.g. “make the width adjustable”.
How to print it
Parts
- hub · PETG · Back face (VESA side) down
115.9 x 160 x 19.3 mm, about 48 g and 66 min at 2 walls/15%. A spine with a channel for the jaws and two wings carrying the VESA holes. M4 nuts press into the wing fronts and into two slots in the side walls.
- jaw-top · PETG · On its side, groove facing up
124.7 mm long at the default height, about 20 g and 32 min. A C-jaw with a closed groove for the knob screw: it lifts 14 mm to let the monitor in and has 3 mm of take-up.
- jaw-bottom · PETG · On its side, detent facing up
110.2 mm long at the default height, about 18 g and 29 min. The knob screw sits in a round detent, so the jaw cannot slide down under the monitor's weight.
- knob ×2 · PETG · Bolt-head pocket face down
17 mm fluted thumb knob, about 1 g and 6 min each. Print in an accent colour if you like.
Print settings
- Layer height
- 0.2 mm
- Walls
- 3 walls recommended (the page stats use 2 walls)
- Infill
- 15%
- Supports
- None. Every part reports 0% support in the engine.
- Notes
- PETG: it is tougher than PLA and survives a warm monitor back. At 2 walls and 15% infill the full set is about 90 g and 2 h 24 min. With 3 walls and 15% (recommended, for firmer nut and screw seats) it is about 116 g and 3 h 7 min. The hub (160 mm long) fits a 180 mm bed. Jaws grow to 151.5 mm long
Hardware
- 2 × M4 x 16 hex-head bolt · Thumb screws: the head presses into each knob.
- 6 × M4 hex nut · Two go in the spine's side-wall slots for the knob screws. Four go in the wing fronts for the VESA screws.
- 4 × M4 x 12 to M4 x 16 screw · VESA screws through the arm plate. Many arms ship with them. Use M4x12 for plates 2-4 mm thick (the check covers M4x12 with a 4 mm plate and M4x16 with a 2 mm plate).
Assembly
- Measure your monitor's height and width, its thickness at the top and bottom edges, and the bezel width from the edge to the picture. Set the sliders before you print.
- Press four M4 nuts into the hex pockets on the wing fronts and two M4 nuts into the slots beside the channel, all from the front (monitor) side.
- Press an M4x16 hex bolt head into each knob's pocket. Add a drop of glue if the fit is loose.
- Hold the hub and slide the bottom jaw into the channel from the bottom end. Thread its knob in from the side until the screw tip drops into the round detent, then tighten.
- Slide the top jaw into the channel from the top end. Thread its knob in until the tip sits in the groove, then back it off half a turn so the jaw slides.
- Screw the hub to the arm's VESA plate with four M4 screws into the wing nuts (75 or 100 pattern, matching the slider).
- Lift the top jaw. Set the monitor's bottom edge into the bottom jaw, tilt it upright against the spine, lower the top jaw over the top edge and tighten its knob.
Good to know
- Load checks cover monitors up to 1.5 kg (the weight slider's maximum), with the set-down load doubled. Do not use it for heavier screens.
- Many gas-spring monitor arms need 2 kg or more to hold position. A light portable monitor may drift up on them. Use a fixed or friction arm, or an arm rated for very light loads.
- The side-port check uses the monitor width you enter and assumes the USB-C ports are on the left and right edges. The mount is 115.9 mm across with the VESA 100 wings, so it ends 67 mm in from each side edge on the narrowest 250 mm setting. Enter your real width.
- The monitor's back must be flat where the spine sits. If the screen is thicker in the middle than at its top and bottom edges, it will not sit flat in the jaws.
- Measure the height to within 1 mm. The top jaw has 3 mm of take-up below the set height.
- The lips are sized to stop 1 mm short of the picture, based on the bezel you enter. Check the bezel at both the top and the bottom edge, since some screens have a wider chin.
- Ports on the top or bottom edge are not covered by the side-port check. The jaws are only as wide as the jaw-width slider, so check that they miss any port there.
- Fits, clamping friction and strength are geometry and load estimates from the Loftsmith engine, not results from a printed part. Print one jaw first to check the throat on your monitor.
Comments