一体打印铰链盒生成器
盖子平放在盒子后方的热床上打印,由一个已经装好的筒形铰链连着。翻过来,就落在盒沿上。关键在于铰链的位置。盖子按合上的状态设计,再沿铰链轴镜像,所以铰链轴位于盒子高度的一半,再加上间隙和盖子厚度。这样打开状态打印的盖子正好合在盒子上。交错排列的铰链节绕着属于盒子的销轴转动,水滴形孔让铰链节的顶部无需支撑也能打印。一圈定位唇边托住合上的盖子。校验涵盖铰链是否自由、盖子是否就位、是否被扣住以及铰链节壁厚,从打开到合上的转动过程会逐个姿态做碰撞检查。

Building the model
Loading the 3D view
No adjustable sizes
Ask for the sizes you want to tweak, e.g. “make the width adjustable”.
What Loftsmith can do
See what Loftsmith designs
Straight from the Loftsmith Workshop, every print check passed. Need a part this page can't make? Describe it and Loftsmith designs it for you.
默认尺寸下的规格
在 Bambu Lab A1 上用 PLA 实际构建测得。拖动上方滑块时,每个数字都会实时更新。
- 整体尺寸
- 80 × 129 × 30 mm
- 零件数
- 2
- 耗材
- 41 g
- 打印时间
- 1 h 6 min
- 打印盘
- 1
- 支撑
- 不需要
工程校验
校验和参数名称直接来自 CAD 引擎,以英文显示。
- Lid prints flat on the bedopen lid bottom at z = -0.00 mm, lip facing up
- Hinge prints free0.35 mm radial and 0.4 mm axial gaps around every knuckle
- Closed lid seats on the rimlip inside the walls, 0.3 mm above the rim when closed
- Knuckles capture the lidthe pin passes through the lid knuckles; the lid cannot lift or slide off
- Pin and knuckle sizes1.65 mm knuckle wall around a 4 mm pin
可调尺寸
| 设置 | 默认 | 范围 |
|---|---|---|
| Width | 80 mm | 50–140 mm |
| Depth | 60 mm | 40–100 mm |
| Box height | 30 mm | 18–60 mm |
| Hinge radial gap | 0.35 mm | 0.25–0.6 mm |
零件清单
| 零件 | 数量 | 尺寸(mm) | 耗材 | 时间 |
|---|---|---|---|---|
| box | 1 | 80 × 69 × 30 | 26 g | 41 min |
| lid | 1 | 80 × 69 × 21 | 15 g | 25 min |
制作方法
- 设置盒子的宽、深、高。
- 第一次打印保持 0.35 mm 铰链间隙;能稳定松开后再调小。
- 按摆放好的样子打印,盖子平放在盒子后面,无需支撑。
- 轻轻掰一下盖子让铰链松开,然后合上。
打印建议
- 注意第一层:让一体打印铰链粘死的元凶就是象脚。
- PLA 或 PETG,3 层壁。铰链节很小,外壁要慢。
常见问题
为什么要打开状态打印?
打开状态下盖子是平的,铰链围绕销轴打印时不需要支撑。镜像设计保证合上时正好落在盒沿上。
盖子能扣紧吗?
壁内侧的一圈唇边负责定位。盖子是合着搭在上面,而不是咔哒扣住,所以不适合倒着拿。
需要目录里没有的形状? 用文字生成 CAD,用你自己的话描述它

Comments