Dust collection hose adapter generator

Every tool port and every hose is a different size, and the size on the label is rarely the size you measure. Give each end the diameter you measured and say whether it slides into or over the hose; the cuff starts loose by the clearance and tightens by the taper, so the hose jams on and stays. The checks confirm the taper grips without splitting the hose, the cone between the two ends prints without supports, the bore keeps most of the smaller hose's airflow and the walls take a hose being twisted on.

Dust hose adapter: 3D-druckbares Modell, 58 × 58 × 92 mm

Building the model

Loading the 3D view

No adjustable sizes

Ask for the sizes you want to tweak, e.g. “make the width adjustable”.

Change it in the Studio

Daten bei Standardgröße

Gemessen am echten Build auf einem Bambu Lab A1 in PETG. Jede Zahl aktualisiert sich live, wenn du oben an einem Regler ziehst.

Gesamtgröße: 58 × 58 × 92 mm
Teile: 1
Filament: 31 g
Druckzeit: 52 min
Druckplatten: 1
Stützstrukturen: Nicht nötig

Technische Prüfungen

Namen von Prüfungen und Parametern kommen direkt aus der CAD-Engine und sind auf Englisch.

Hose jams on the taper0.8 mm over each cuff (0.4 to 2 mm grips without splitting the hose)
Cone prints without supports38 deg from vertical over 12 mm
Airflow kept through the bore34.6 mm narrowest bore, 98% of the smaller hose's area
Walls hold a hose being twisted on2.4 mm walls

Anpassbare Maße

Einstellung	Standard	Bereich
End A: measured hose or port diameter	58 mm	20–130 mm
End A slides inside the hose or port	an	an / aus
End A cuff length	40 mm	20–80 mm
End B: measured hose or port diameter	35 mm	20–130 mm
End B slides inside the hose or port	aus	an / aus
End B cuff length	40 mm	20–80 mm
Wall thickness	2.4 mm	1.6–4 mm
Clearance at the tip (diameter)	0.4 mm	0–1.5 mm
Taper over each cuff (diameter)	0.8 mm	0–2.5 mm

So wird’s gemacht

Measure the inside or outside of each hose or port with calipers, not the label.
Set both diameters, tick which ends slide inside, and set each cuff length.
Print standing on the wider end, 3 walls, no supports; if a cuff is loose, raise Taper by 0.2 mm.

Drucktipps

PETG or PLA, 0.2 mm layers, 3 walls, 0 to 10% infill: the part is all wall.
Stand it on its wider end; the cone leans less than 45 degrees so it needs no supports.
Ribbed and flexible hoses stretch, so they take a bigger taper than a rigid tool port.

Häufige Fragen

Which size do I type: inside or outside diameter?

The size of the surface the adapter touches. For an end that slides inside a hose, measure the hose's inside diameter; for an end that slips over a port, measure the port's outside diameter. Then tick the inside box to match.

Why is the cuff tapered?

A straight cuff is either loose or impossible to push on. A taper of about 0.8 mm over the cuff starts loose and tightens as the hose goes home, so it jams by friction and pulls off again by hand.

Does it need supports?

No. The cone between the two ends is kept at 45 degrees or less from vertical, and the checks tell you if a setting breaks that.

Du brauchst eine Form, die nicht im Katalog ist? Beschreib sie in deinen eigenen Worten mit Text zu CAD

I printed this Remix